part of the new case i'm still working on , modules : Serge gamalan VCO's ,Serge Wavemultiplier (middle section) ,Polivoks VCF ,Yamaha GX Resonator ,Serge Phaser ,Morphlag ,3 Channel Mixer . the case is 2 x 17 inch panels .

part of my first 4U case , modules : 2 x Serge vcs , Serge extended adsr ,Buchla 111 ,Grant Richter Hardware Neurons ,Serge Smooth and Stepped gen.

NLC Jerk together with Buchla Fluctating Random Voltages on panel with additional Noise Source .

6 Stage Programmer from Synapse Magazine by Serge with additional 1 or 2 octave switch on two rows .Sidenote that the panels were printed poorly as all i wanted was to plug in stuff at the time.

Synthesizer DIY

simple pattern with Quantized Random Voltages from Buchla < Improvised 4 step seq . MFOS VCO's ,Serge Waveshaper ,Double Pulse by Ian Fritz ,VC Echo ,SSG Stepped Input in Sequencer Hold input

Double Pulse waveform generator

the Waveforms from Double Pulse Waveform Gen from Ian Fritz http://ijfritz.byethost4.com/sy_cir5.htm ,after a while i realized that my MFOS VCO's don't have a clean tri and there is a glitch in the rising part of the triangle )

Few modules in the new case : Dual MFOS VCA ,Serge Sequential Pulse ,Neuron+Comparator ,VC Echo ,3 channel Mixer with attenuated output ,these are poorly printed panels as i was in a rush to plug in the modules :-)

a new case ,almost all DIY ,and white ,with distro boards on each side ,big heatsinks ,and only one pair of rails

Homemade Serge - 17 feb

My Homemade Serge - esque system going thru Cuvave DIG-REVERB

Here is another 17'' Panel for a classic Serge ,this one has room for PSU switch on the side as i planned to have the PSU inside a case.

Homemade Serge - feb 2019

VCS acting on LPF output from Serge '73VCF ,random decay on Extended ADSR

This is another project i couldn't aford to finish - a classic Serge .Here is collected from the webs various paperface panels into 17 inch .

Patch with Experimental Hardware Neurons module that drives a minimal system .

This is another beginner's circuit ,and one of the first i got working ,and is really simple and working fine for a total of 10 parts count ,so here it is a toy sample and hold by Osamu Hoshuyama ,the pcb is 60x60 mm and not tested yet

EFM Wildcat LFO ,this was the first module i ever got working ,so i just made a PCB for it ,it's 60x60 mm and it's really low-parts count so it's good for beginners ,and one more lfo is always welcome .The 14 pin chip is TL074.

 

I finished this case , finally!!! It took me so much time ,and now to show off :)
the case has these modules : 
MFOS VCO x 2 
111 Buchla Ring Mod x 2 
Serge Botom Wavemultiplier x 1 
NLC B0ngo x 2 
Serge '73 VCF x 1 
Hip Bass Drum x 1 
CGS CV Processor / Mixer 
Serge VCS x 2 
Serge Extended ADSR x 1 
NLC Difference Rectifier x 1 
Grant Richter's Experimental HArdware Neurons 
Serge SSG 
CGS Slope Detector 
Buchla QRV 
Osamu Hushuyama Passive Tone control 


the inside is messy ,this one is not for photo

PAIA 2720-3B VC Bandpass Filter adaptation by gasboss775 as posted earlier on electro-music ,PCB is 70x100mm 

NLC Bong0 and two Stombox adapters from CGS on a stripboard ,i didn't liked as much the 808 Tom i built ,so this will replace it